Dimming Actuators
62%
- The KNX/DALI Gateway communicates with up to 64
- DALI actuators per channel. These can be connected and dimmed in up to 16 groups per channel.
- The gateway also supports selected sensors with DALI interface.
- It also records and transfers DALI status and error messages.
- An individual name, a group, parameter and scenes are assigned to individual DALI ECG´s during commissioning with the ETS (Engineering Tool Software).
- DALI sensors and their functionality are also assigned in the ETS.
- All DALI subscribers and functions are independent and can be linked via group addresses.
- The device can only be operated in DALI segments with connected ECGs and sensors and not with further DALI controllers within the segment (no multi-master mode).
- The power needed for ECGs and sensors is supplied directly through the gateway. An additional DALI power supply is not required, neither is it permitted.
62%
- Power supply: via KNX Bus line, 20VDC
- Rated voltage: 120V AC +10%/-15%, 50/60 Hz
- Rated current:
- 2-channel: 2x1.3A@cosФ=1.0
- 1-channel: 1x2.2A@cosФ=1.0
- N-system DIN-rail mounted device, width:4MU(1MU=18mm)
- Load output:Lamp type2 channels1 channel
Incandescent lamps 150 W250 WLow voltage halogen lamps
with magnetic transformers
120 VA200 VADimmable LED <= 50 VA<=50 VA
62%
- The device can be configured with Desigo Room Automation commissioning tool (ABT) or with KNX Engineering Tool Software (ETS).
- Protruding wires stranded AWG 12
- A phase connection for an output that is equipped with a relay contact per output as a switching element
- Contact rated operational voltage AC120 V, AC 230 V, AC 277 V, AC 347 V
- Contact rated operational voltage AC / DC 24 V
- Contact rated current according to DIN EN 60669-1: 16 A / 20 A (resistive load)
- Fluorescent lamp load according to DIN EN 60669-1: 16 AX / 20 AX (200 µF) at AC 230 V
- Bus-powered electronics
- Integrated bus coupling unit
- Bus connection via bus terminal
- Red LED for display of the activation of the addressing mode as well as the operational readiness
62%
- Protruding wires stranded AWG 12
- A phase connection for an output that is equipped with a relay contact per output as a switching element
- Contact rated operational voltage AC 120 V, AC 230 V, AC 277 V, AC 347 V
- Contact rated operational voltage AC/DC 24 V
- Contact rated current according to DIN EN 60669-1: 16 A / 20 A (resistive load)
- Fluorescent lamp load according to DIN EN 60669-1: 16 AX / 20 AX (200 µF) at AC 230 V
- Bus-powered electronics
- Integrated bus coupling unit
- Bus connection via bus terminal
62%
- Output for switching and dimming resistive, inductive or capacitive loads
- Automatic adjustment to leading edge or trailing edge control, depending on the type of load
- Rated frequency 50...60 Hz
- Electronic protection of the output against overload, short circuit and temperature rise
- Bus-powered electronics
- Integrated bus coupling unit, Bus connection via bus terminal block
- Type of protection: IP 20
- Rated operational voltage AC 120 V
62%
- Outputs: Eight outputs (latching relays, potential-free contacts)
- Electrical rating per output:ac/
- 347 Vac, 50/60 Hz, 15A , cos phi = 1
- 277 Vac, 50/60 Hz, 20A , cos phi = 1
- 1.5 HP @ 120 Vac
- 3 HP @ 277 Vac
- Control voltage: 1 to 10V (provided by ECG Dynamic ballast)
- Dimmable electronic ballast: Maximum 60 units
- Signal amplifier: Maximum 12 units
Expert picks
$295.00
$45.00
$237.61
Newest Products
$38.00
$48.00
$100.00
KNX Training
$1,500.00
$1,200.00
